SuperOrganic wall covering is a unique and eco-friendly option for decorating your interior. Made from natural materials such as organic hay, flower petals and wooden straws, it offers an authentic and eco-friendly aesthetic.

SuperOrganic’s large format panels are easy to install, because they stick directly to the wall, in the same way as traditional wall coverings. This allows you to give your space a natural look without having to carry out major renovation work.

By using natural materials, SuperOrganic creates a warm and soothing atmosphere in your interior. Additionally, these materials are often recyclable and biodegradable, making them a sustainable choice for your wall decor.

Whether you want to bring a touch of nature to your living room, bedroom or even your work space, SuperOrganic wall covering offers an aesthetic, environmentally friendly and easy to install solution.

Collections

Technical sheet

Installation

Thin and flexible panel made of 3 layers of untreated, glue-backed, textured veneer. Homogeneous and without black edges, 3Dply has a finish similar to that of solid wood. The panels come sanded and untreated, therefore they must be varnished or oiled once glued back onto a substrate. It is also possible to stain the wood surface before applying the finish. The 6 textures of 3Dply come in 10 wood species.

Flexible panel – to bond on a substrate – composed of 3 plies of unfinished veneer laminated together and textured. 1,3 mm thick, homogeneous, without any black line on the edges (no kraft paper). Easy to install.

Finishing: supplied unfinished. To be varnished or oiled. Or to be stained before applying the finishing.
Available species: Oak (see opposite side), Mahogany, Anigre, Canadian Maple, Light Ash, Steamed Beech, American Cherry, American Walnut, Sycamore and Wenge.

Dimensions – first dimension indicates the wood grain direction:

Standard: 2520 x 1270 mm and 3050 x 1270 mm

Doors dimensions: 2150 x 950 mm / 2150 x 1270 mm / 2520 x 950 mm / 3050 x 950 mm

Matched edge bandings : yes

Total thickness : 1,3 mm
Bending: cold bending up to 100 mm radius, either parallel or perpendicular to the wood grain.

Fiche technique

Collection

Solid-colored decorative laminates coated with an anti-fingerprint finish. With a very soft touch, they offer non-stick properties. They are easy to clean and reduce the use of cleaning agents. The surfaces remain always impeccable, even when subjected to intensive use. Their ultra-matte finishes also guarantee a low degree of gloss. This new collection is available in the 25 iconic Pure Paper Color references, one of the widest color range on the market.

High pressure laminate (HPL) with anti-fingerprint Oberflex finish. Matte color. Extra smooth surface. Very soft touch, the product offers non-stick properties for an easy maintenance.

Technical product thanks to its very high resistance (complying with the requirements of the EN 438 standard)

Standard dimension : 3050 x 1270 mm

Other dimensions on demand :

• 2150 x 950 mm
• 2520 x 950 mm
• 2520 x 1270 mm
• 2150 x 1270 mm
• 3050 x 950 mm

Matched edge bandings : PVC 1 mm edge bandings x 25 colours of the collection

Obersound acoustic panels compatibility : yes

Fire ratings : M1, Bs2d0 or IMO on demand

Datasheet color Anti-fingerprint 

Collections

Oberflex

New usage for Oberflex wood panels : write with pen or chalk and put up or fix accessories using magnets
http://www.oberflex.com/416–smart-surface.html

Pure Paper

New usage for Pure Paper laminates : write with chalk and put up or fix accessories using magnets

Colors

The unanimously acknowledged aesthetic qualities of Oberflex products are the result of rigorous selection of the finest types of wood from the world’s top suppliers.

PEFC certification guarantees that all our wood comes from sustainably managed forests.

Optimisation

Each batch of veneer sheets comes from a single log in order to ensure maximum homogeneity in terms of colour and structure. Thanks to the precise slicing involved, a single log may provide several thousand square meters of veneer: 1m3 of wood gives an average of 1500m2 of veneer.

Verification

Upon receipt, each package of veneer sheets is opened by hand and checked by the naked eye in order to remove any non-standard sheets or batches and prevent any aesthetic fault.

Assembly

The sheets display different structures depending on whereabouts in the slicing process they come from: the “slabwood” or the “squared” part. They are then sorted by colour and joined in a number of ways: regular if we are looking for a “cabinetwork” effect (a symmetrical or repeated motif) or irregular if a “massive” effect is sought. The sheets of wood are prepared in this way before receiving the special treatment that will turn them into an Oberflex product.

Finish

At this stage, the veneer may benefit from a surface treatment that will make the product extremely hard-wearing.

A number of finishes are available: matt or satin, silk, sanded or relief.

So many effects, all intended to meet the expectations of our clients and enhance our range of panels, to which we may add aesthetic and acoustic perforations, standard or customised.

Valorisation

A final manual check on the finished product allows us to discard any product displaying a fault in its appearance or technical quality. Since Oberflex doesn’t supply seconds, the waste material is valorised in our biomass boiler, which supplies our workshops with their basic energy.

The particularity of the Oberflex collection lies in its high resistance finish. Oberflex laminated wood veneer panels are coated with a specific finishing layer which gives them great durability and increased resistance to impacts, scratches and stains. This finish protects the wood while maintaining its natural appearance and texture.

In addition, the Oberflex collection offers a wide variety of choices with more than 200 references of laminated wood veneers, which makes it possible to find solutions adapted to all styles and projects.

Optimisation

Each batch of veneer sheets comes from a single log in order to ensure maximum homogeneity in terms of colour and structure. Thanks to the precise slicing involved, a single log may provide several thousand square meters of veneer: 1m3 of wood gives an average of 1500m2 of veneer.

Verification

Upon receipt, each package of veneer sheets is opened by hand and checked by the naked eye in order to remove any non-standard sheets or batches and prevent any aesthetic fault.

Assembly

The sheets display different structures depending on whereabouts in the slicing process they come from: the “slabwood” or the “squared” part. They are then sorted by colour and joined in a number of ways: regular if we are looking for a “cabinetwork” effect (a symmetrical or repeated motif) or irregular if a “massive” effect is sought. The sheets of wood are prepared in this way before receiving the special treatment that will turn them into an Oberflex product.

Finish

At this stage, the veneer may benefit from a surface treatment that will make the product extremely hard-wearing.

A number of finishes are available: matte or satin, brushed and relief.

So many effects, all intended to meet the expectations of our clients and enhance our range of panels, to which we may add aesthetic and acoustic perforations, standard or customised.

Valorisation

A final manual check on the finished product allows us to discard any product displaying a fault in its appearance or technical quality. Since Oberflex doesn’t supply seconds, the waste material is valorised in our biomass boiler, which supplies our workshops with their basic energy.

BORG! is a collection of 6 textured wood panels available in 6 natural wood species. Inspired by traditional woodwork, the reliefs are particularly pronounced and give the panels a natural and high quality depth effect.

Drapa

Vag

Fara

Skarp

Till

Fibra

Document

Borg!.pdf

A 3D suspended ceiling system for creating new rhythms

Continent

The continental plates which form the surface of these models, drift and divide to offer graphic ceilings with flat surfaces.

Faille

These breaks in the ground trigger vertical displacements of independent plates. The ceilings rise and fall to form landscapes of differing altitudes.

Éruption

The magma thrust results in real explosions which tear apart the surfaces and give rise to a series of ceilings to rugged terrain.

Glissement

The movement of the plates through slipping generates ceiling structures with dizzying slopes. The blocks overlap, collide and seem always in motion.

System

An original patented mounting system

Central to Tectonique 5.5’s innovation, the mounting system dreamed up by the 5.5 designers allows you to install tiles that are angled or staggered to create volumes and rhythms, that could, until now only be achieved by costly custom solutions. Tectonique 5.5 is composed of new hangers, hooks and profiles specifically developed and designed for installing all the system’s models.

Composition of the Tectonique 5.5 tile

With a new covering and new composition, the Tectonique 5.5 tile meets ambitious size and functional objectives. It benefits from the latest innovations of Oberflex’s research and development department in terms of aesthetics and industrial processes.

New generation wood veneer laminate

The Tectonique 5.5 tile is covered on its visible face with a real wood, new generation veneer laminate. Phenol-free, the veneer laminate face contributes to controlling the environmental impact of Tectonique 5.5. With an “A+” rating for VOC emissions, the tiles conform to air quality standards.

A brand new composition from Oberflex

The Tectonique 5.5 tile is composed of a particle board wood frame and a honeycomb cardboard body. Thanks to this new composition, it is light and easy to handle, while meeting the challenges of flatness, thickness and stability.

Because its weight has been reduced, the thickness of the tile can be increased to improve the visibility of the sections and enhance the aesthetics of the designs.

Installation

Composed of a patented mounting system and lightened tiles, Tectonique 5.5 is easy to grasp. Installation requires no special tools and all the markers are adjusted and adapted for mounting and removal which is both simple and accurate. An installation guide and a predefined drawing for each model provides fast understanding of the system.

Acoustic qualities

A new approach regarding acoustics of your spaces

Control of a building’s sound quality is obtained by the balance between absorption, diffusion and reflection of the sound. Tectonique 5.5 ceilings, due to their shapes and relief forms, directly influence these three acoustic characteristics. The choice of a model will therefore be made according to its relief and openings, taking into consideration the layout of the space and the acoustic effect being sought.

Absorption

Sound absorption is the ability of a wall to partially absorb a sound wave and only to return a part of the energy received to the point of departure. This property thus helps reducing reverberation in a space and increases the acoustic comfort and the intelligibility of speech. The sound absorption of Tectonique 5.5 ceilings, is created by the position of the tiles and the spaces between them and by the characteristics of the material.

Reflection

Reflection is a physical phenomenon by which a surface returns a portion of the sound waves. It is the type of surface and the nature of the material which affect the reflection of a sound wave. The surface of Tectonique 5.5 tiles contributes to controlling sound reverberation. A part of the wave is reflected whereas the other part enters the material.

Diffusion

When a sound wave encounters a flat obstacle, the angle of reflection is equal to the angle of incidence, same as a mirror. If the surface has relief forms and shapes, the obstacle becomes a point of dissemination and the sound wave is sent back in all directions. The relief forms and the changes of planes of Tectonique 5.5 ceilings create this dissemination and limit the areas of focus of the sound and echoes. This more diffuse and homogeneous acoustic enriches the sound balance of the space.

The evaluation of these three acoustic characteristics is provided in the data sheets for each model. These give guidance in aimed at comparing the potential of acoustic correction of one model in relation to another.

Obersound® acoustic panels are designed to improve acoustic comfort in interior spaces by reducing sound reflection. Used on walls or ceilings, they improve speech intelligibility and sound clarity.

The perforations in the decorative cladding give these panels an additional function: sound absorption. The partial absorption of sound waves significantly reduces the sound reverberation and the effects of resonance or echo.

Obersound perforation patterns can be applied to all Oberflex decorative surfaces (real wood, solid colors or metal). They are divided into 4 collections and are customizable.

Obersound configurator

www.obersound.com/create

Micro-perforation

Invisible peroforations due to micro-perforation process. The aesthetic appearance is preserved while offering high acoustic performances.

Micro-grooves

Discreet and elegant micro-grooves milled directly fron front side of the panel. One of the highest absorption coefficients on the market. The 6 micro-grooved patterns are available on real wood panels (70 species) or solid colors extra matt (25 colours).

Classics

The basics for a discreet look. The panels feature round, oblong or grooved-perforated.

Actions 5.5

The new collection of customizable acoustic panels. 6 models that can be configured into an infinite number of perforated patterns.

Customizable patterns

Collections 5.5

Five collections designed by Studio 5.5. Each collection features five patterns: an architectural skin, a space garment, a living wall, a vibrating panel or a landscape.

25 acoustic perforation models with enhanced graphic identity

Documents

Obersound Acoustic Performances EN.pdf